C型钢广泛应用于钢结构建筑檩条、墙梁等，也可自组装成轻型屋面框架、支架等建筑构件，C型钢安装需要调整一些部位，哪些部位需要调整?下面济南C型钢厂为您分析：

C-shaped steel is widely used in steel structure building purlins, wall beams, etc. It can also be self-assembled into lightweight roof frames, brackets, and other building components. Some parts of C-shaped steel installation need to be adjusted, and which parts need to be adjusted? Below, Jinan C-beam Steel Factory will analyze for you:

1、调整垂直轮。

1. Adjust the vertical wheel.

2、按照a面调整方法，依次调整6-9个通道;

2. Adjust 6-9 channels in sequence according to the A-side adjustment method;

3、调整第五个滚轮通过改变间隔套，以满足所需的大小。中间左右;

3. Adjust the fifth roller by changing the spacer to meet the required size. Middle left and right;

4、带材轧制通过一排轴后，调整一轴上的两轮，使边缘轧制达到要求(1.5-50px);

4. After the strip passes through a row of shafts, adjust the two wheels on one shaft to make the edge rolling meet the requirements (1.5-50px);

5、间隙调节:根据带钢的厚度，用塞子调节每排轴上下轮之间的间隙，使之达到要求的距离;

5. Gap adjustment: According to the thickness of the strip steel, use plugs to adjust the gap between the upper and lower wheels of each row of shafts to achieve the required distance;

6、调整喂料垂直轮(整平轴前后各一对)，使喂料平整、平整，带钢平直。将轧制后的带材平整成一排轴;

6. Adjust the feeding vertical wheels (one pair at the front and one pair at the back of the leveling shaft) to ensure that the feeding is flat and even, and the strip steel is straight. Flatten the rolled strip into a row of shafts;

7、启动机器使带钢在两轴上轧辊，调整两轴的两个轮子，使两轮子的外缘与一轴的压痕重合，确保两辊压痕前后一致;

7. Start the machine to roll the strip steel on both axles, adjust the two wheels on both axles to make the outer edges of the two wheels coincide with the indentation on one axle, and ensure that the indentation on both rollers is consistent before and after;

8、基准面:用尺子在轮轴和后轮(13道)的同一端测量垂直板的尺寸。使数据相同。然后用尺子测量两轴两端和底梁的尺寸，使数据相同;

8. Reference plane: Use a ruler to measure the dimensions of the vertical plate at the same end of the axle and rear wheel (track 13). Make the data identical. Then use a ruler to measure the dimensions of both ends of the two axes and the bottom beam, so that the data is the same;

9、调直调平:在一根轴和下一根轴的两端用细线制作，其余11根轴与这两根轴调平。在细线前后做准中线，调整其他11个轮子，使它们都在同一中线上。

9. Straightening and leveling: Make thin wires at both ends of one shaft and the next shaft, and level the other 11 shafts with these two shafts. Align the centerline before and after the thin line, and adjust the other 11 wheels to make them all on the same centerline.

虽然c型钢有许多优点，但安装过程中的注意事项尤为重要。c型钢的安装将直接影响工程质量，因此安装需要严格按照操作流程进行。更多相关事项就来我们网站http://sxhtyz.com咨询吧！

Although C-shaped steel has many advantages, precautions during installation are particularly important. The installation of C-shaped steel will directly affect the quality of the project, so the installation needs to be strictly carried out in accordance with the operating procedures. For more related matters, come to our website http://sxhtyz.com Consult!