为了让彩钢材料在市场上更加的受欢迎，很多厂家也在不断的进行创新，开始加工生产颜色丰富的产品，在彩钢板上面进行喷涂油漆，但是有些彩色板在使用的时候，经常会出现爆漆现象，那么这种问题应该怎么解决呢？大家清楚吗？

In order to make color steel materials more popular in the market, many manufacturers are also constantly innovating, starting to process and produce products with rich colors, and spraying paint on color steel plates. However, some color plates often appear paint explosion when used. How should this problem be solved? Are you clear?

应先加入钝化溶液，然后再加入水。由于钝化液的密度，如果钝化液的密度高于水的密度，原料混合不均匀，钝化层与基体的附着力差，容易造成彩钢表面爆炸。

Passivation solution shall be added before water. Due to the density of the passivation solution, if the density of the passivation solution is higher than the density of water, the raw materials are mixed unevenly, and the adhesion between the passivation layer and the matrix is poor, which is easy to cause the surface explosion of color steel.

钝化板的温度生产过程规定每2小时检查一次，因为济南彩钢复合板厂的工作人员没有定期跟踪钝化板的温度。尤其在冬季，温度在2小时内变化很大，会导致彩钢复合板的失效。当压力过高时，会出现刮掉油漆的现象。

The temperature of the passivation plate shall be checked every 2 hours in the production process, because the staff of Jinan color steel clad plate factory did not regularly track the temperature of the passivation plate. Especially in winter, the temperature changes greatly within 2 hours, which will lead to the failure of color steel clad plate. When the pressure is too high, the paint will be scraped off.

在彩钢复合板的生产过程中，出口检验镜上有灰尘、滚轮和一些灰尘，会直接影响彩钢复合板的表面质量，开始时可能不会显示出来，但时间长了，或者在阳光照射下会出现喷漆现象。

In the production process of color steel clad plate, there are dust, rollers and some dust on the export inspection mirror, which will directly affect the surface quality of color steel clad plate. It may not be displayed at the beginning, but it will be painted for a long time or under the sun.

配置罐体时，先加钝化液，再加水。例如钝化液的密度，如果钝化液的密度高于水，则原料混合不均匀，钝化层与基材的附着力就会较差，即板材表面就很容易爆漆。

When configuring the tank, add passivation solution first, and then add water. For example, the density of the passivation solution. If the density of the passivation solution is higher than that of water, the raw materials are mixed unevenly, and the adhesion between the passivation layer and the substrate will be poor, that is, the surface of the plate is easy to explode.

还有一个问题就是钝化板温度的生产过程需每2小时检查一次，因为工作人员在检查的时候并没有定期跟踪钝化板温度。尤其是冬天，2小时内的温度变化比较大，会导致板材失效，按压时会出现划伤和掉漆的现象。

Another problem is that the passivation plate temperature should be checked every 2 hours during the production process, because the staff did not regularly track the passivation plate temperature during the inspection. Especially in winter, the temperature change within 2 hours is relatively large, which will lead to plate failure, and scratch and paint falling will occur when pressing.

济南彩钢瓦厂认为板材在生产过程中，出口检查镜和部分辊子上会有灰尘，政协灰尘会直接影响板材的表面质量，或者一开始表现的不是很明显，但时间一长，在阳光暴晒下就会出现爆漆。

Jinan color steel tile factory believes that there will be dust on the export inspection mirror and some rollers during the production process of the plate. The dust will directly affect the surface quality of the plate, or it is not very obvious at first, but over time, the paint will explode under the sun.

以上是今天为大家分享的关于济南彩钢复合板爆漆现象的原因，也希望大家在使用过程中注意维护，如对这一问题还存在任何疑问，都欢迎关注我们网站http://sxhtyz.com并咨询我们的工作人员，将竭诚为您服务。

These are the reasons for the paint explosion of Jinan color steel clad plate shared today. We also hope that you will pay attention to maintenance during use. If you have any questions about this problem, you are welcome to pay attention to our website http://sxhtyz.com And consult our staff, will serve you wholeheartedly.